HONDA NSF250R NEW HANDLEBARS, LEVERS & FOOTPEGS 2021
Please 'Refresh' this page every time you visit. If it is slow to reload, you know then that this page has been updated since your last visit.
Honda NSF250R SpeedFiber 2019/2021 Front Fairing Stay / Clock Mounting Bracket £185.00 + VAT
|
|
|
HONDA NSF250R HANDLEBARS & LEVERS
22mm FORWARD EXTENDED HANDLEBAR CLAMPS - Pair (for standard Honda RS125 Forks Ø 44mm) £165.00 + VAT
22mm FORWARD EXTENDED HANDLEBAR CLAMPS - Pair (for Ohlins Forks Ø 45mm) £165.00 + VAT
22mm FORWARD EXTENDED HANDLEBAR CLAMPS - Pair (for Ohlins Forks Ø 45mm) £165.00 + VAT
|
|
BATTLE FACTORY ALUMINIUM HANDLEBAR - with nylon end cap £16.50 + VAT each
BATTLE FACTORY HANDLEBAR END CAP £2.50 + VAT each
BATTLE FACTORY HANDLEBAR END CAP £2.50 + VAT each
|
|
|
RENTHAL HANDLEBAR GRIPS
Road Race Full Diamond Handlebar Grips £9.50 + Vat per pair (x2 Grips)
'Soft' Light Grey G147
'Medium' Grey G148
'Firm' Dark Grey G149
Road Race Full Diamond Handlebar Grips £9.50 + Vat per pair (x2 Grips)
'Soft' Light Grey G147
'Medium' Grey G148
'Firm' Dark Grey G149
HONDA RS125 BREMBO BRAKE LEVERS
Brembo 'Short' 18 Front Brake Lever £43.50 + VAT
Brembo 'Standard' Front Brake Lever £45.00 + VAT
Brembo 'Standard' Front Brake Lever £45.00 + VAT
Top: Brembo Short 18 Front Brake Lever
Bottom: Brembo Standard Front Brake Lever
BREMBO 'FOLDING' BILLET BRAKE LEVER - Short 18 length £73.00 + VAT
BREMBO 'FOLDING' BILLET BRAKE LEVER - Standard 250 length £73.00 + VAT
BREMBO 'FOLDING' BILLET BRAKE LEVER - Standard 250 length £73.00 + VAT
HONDA NSF250R FRONT BRAKE LEVER PROTECTOR
Honda NSF250R FRONT BRAKE LEVER PROTECTOR - RIGHT SIDE ONLY - PROGUARD SYSTEM £46.00 + VAT
Suitable for all 22mm handlebars with hollow ends and minimum inside diameter 14mm to maximum inside diameter 20mm
Please note: If using the Battle Factory Handlebars, it is necessary to turn around the handlebars to use the smaller inside diameter end.
We would advise using Loctite 243 threadlocker on all nuts and adjuster grub screws.
Honda NSF250R FRONT BRAKE LEVER PROTECTOR - RIGHT SIDE ONLY - PROGUARD SYSTEM £46.00 + VAT
Suitable for all 22mm handlebars with hollow ends and minimum inside diameter 14mm to maximum inside diameter 20mm
Please note: If using the Battle Factory Handlebars, it is necessary to turn around the handlebars to use the smaller inside diameter end.
We would advise using Loctite 243 threadlocker on all nuts and adjuster grub screws.
|
|
|
Honda NSF250R FRONT BRAKE LEVER PROTECTOR - RIGHT SIDE ONLY - GB RACING £46.00 + VAT
GB Racing Front Brake Lever Guard : For 16~17mm Internal Handlebar Tube Diameter
GB Racing Front Brake Lever Guard : For 16~17mm Internal Handlebar Tube Diameter
- Revolutionary new tough, high-impact composite material made from 60% Long Glass Fibered Nylon
- PATENT # GB2479405 for Improved Composition
|
|
|
HONDA NSF250R CLUTCH LEVERS
PATTERN CLUTCH LEVER £18.00 + VAT
HONDA NSF250R FOOTPEGS HANGERS, FOOTPEGS, GEAR & REAR BRAKE LEVERS
RCD GP PATTERN FOOTPEG (8mmThreaded fixing) with Nylon End Cap £17.50 + VAT each
Machine Cut Grooves, giving superior grip over conventional knurled finished footpegs.
Fitted with solid Black Acetal End Cap.
Machined 19mm slot for easy installation / removal using a 19mm spanner.
8mm Threaded Mounting.
Total Length including End Cap : 80mm / Centre Outside Diameter : 24mm / End Outside Diameter : 26mm
Machine Cut Grooves, giving superior grip over conventional knurled finished footpegs.
Fitted with solid Black Acetal End Cap.
Machined 19mm slot for easy installation / removal using a 19mm spanner.
8mm Threaded Mounting.
Total Length including End Cap : 80mm / Centre Outside Diameter : 24mm / End Outside Diameter : 26mm
|
|
|
|
BATTLE FACTORY FOOTPEG (Threaded fixing) with Nylon End Cap & Stud for GP Bearing Lever £22.50 + VAT each
|
|
SPEEDFIBER FOOTPEG with Nylon End Cap £22.50 + VAT each
Please Note: The Speedfiber Footpegs are not threaded.
They have a 8.25mm straight hole and need to be bolted to the footrest hanger, using an 8mm Cap Screw. (*Screws not supplied)
|
|
|
HONDA NSF250R FOOTREST HANGERS
RCD PATTERN FOOTREST HANGER PLATE - Stronger & Lighter Than Standard - CNC Machined £42.50 + VAT each
Fits to both Left & Right Sides
Stronger & Lighter than Standard Honda (255g)
CNC Machined from solid billet 6082 t6 Aerospace grade aluminium.
Fits to both Left & Right Sides
Stronger & Lighter than Standard Honda (255g)
CNC Machined from solid billet 6082 t6 Aerospace grade aluminium.
|
|
|
HONDA NSF250R FOOTREST HANGER EXTENSION PLATES & EXTENDED GEARCHANGE RODS
FOOTREST HANGER EXTENSION PLATE SET £39.00 + VAT
These plates allow you to keep your existing footrest hangers and move them back either 13 mm, 25 mm or 38 mm
Made from high quality HE30 aluminium
Note: Necessary to use extended gear change rod.
Standard Length Gearchange Rod 243mm £10.00 + VAT
13mm Extended Length Gearchange Rod 256mm £10.00 + VAT
25mm Extended Length Gearchange Rod 268mm £10.00 + VAT
38mm Extended Length Gearchange Rod 281mm £10.00 + VAT
These plates allow you to keep your existing footrest hangers and move them back either 13 mm, 25 mm or 38 mm
Made from high quality HE30 aluminium
Note: Necessary to use extended gear change rod.
Standard Length Gearchange Rod 243mm £10.00 + VAT
13mm Extended Length Gearchange Rod 256mm £10.00 + VAT
25mm Extended Length Gearchange Rod 268mm £10.00 + VAT
38mm Extended Length Gearchange Rod 281mm £10.00 + VAT
|
Picture above shows a footrest hanger mounted at 38mm Extended
|
HONDA NSF250R BATTLE FACTORY GEAR CHANGE RODS
Battle Factory Gear Change Rods, for use with the Battle Factory Quickshifter
Battle Factory Standard Length Gearchange Rod 160mm £31.50
Battle Factory 20mm Extended Length Gearchange Rod 180mm £31.50
Battle Factory 50mm Extended Length Gearchange Rod 210mm £35.50
Battle Factory Standard Length Gearchange Rod 160mm £31.50
Battle Factory 20mm Extended Length Gearchange Rod 180mm £31.50
Battle Factory 50mm Extended Length Gearchange Rod 210mm £35.50
|
|
HONDA NSF250R GEAR & REAR BRAKE LEVERS
Honda NSF250R SpeedFiber Lightweight Gear Lever £80.00 + VAT
Gear Lever End can be moved 7.5mm closer towards the footpeg, which helps smaller riders who have small feet.
Honda NSF250R SpeedFiber Lightweight Gear Lever £80.00 + VAT
Gear Lever End can be moved 7.5mm closer towards the footpeg, which helps smaller riders who have small feet.
|
|
|
Honda NSF250R SpeedFiber Lightweight Rear Brake Lever £80.00 + VAT
Better clearance over the NSF250R Exhaust Silencer end can
|
|
|
BATTLEFACTORY G.P. SPEC BEARING TYPE GEAR LEVER - Increased Leverage & No Side Play £84.50 + VAT
BATTLEFACTORY G.P. SPEC BEARING TYPE REAR BRAKE LEVER - No Side Play £84.50 + VAT
|
|
|
HONDA NSF250R FOOTREST HANGER & LEVER COMPLETE SETS
BATTLE FACTORY FOOTREST HANGER SET - Footpeg Position Standard £325.00 + VAT
|
|
|
BATTLE FACTORY LEVER REPLACEMENT PARTS
BATTLE FACTORY Replacement Lever End £21.00 + VAT
BATTLE FACTORY Replacement Lever Bearing (x2 in each lever) £12.00 + VAT each
BATTLE FACTORY Replacement Lever Aluminium Collar (28x2.5x2) for pack of x2 £5.75 + VAT
BATTLE FACTORY Replacement Lever Shim Washer (8x0.5x4) for pack of x4 £1.20 + VAT
|
|
HONDA NSF250R SPEEDFIBER GEAR LEVER & REAR BRAKE LEVER END
Honda NSF250R SpeedFiber Replacement Lever End (Length 40mm & Rubber Diameter 17mm) £10.00 + VAT
|
|
Exports of all parts supplied outside of UK, to EU Countries, USA, Australia, South Africa, Asia etc are exempt from UK VAT and will be charged 0% VAT.
On arrival to your destination country, you may be asked to pay additional duties and taxes by customs, before the shipment is delivered.
Import tax, customs & duties regulations vary from country to country.
Payment of all Import tax, customs & duties charges are the responsibility of the customer.
On arrival to your destination country, you may be asked to pay additional duties and taxes by customs, before the shipment is delivered.
Import tax, customs & duties regulations vary from country to country.
Payment of all Import tax, customs & duties charges are the responsibility of the customer.
SP125 Limited
22 Walker Wood, Baildon, Shipley, West Yorkshire, BD17 5BE, England
Telephone 01274 583231 steve@sp125racing.com Mobile 07738 626165
22 Walker Wood, Baildon, Shipley, West Yorkshire, BD17 5BE, England
Telephone 01274 583231 steve@sp125racing.com Mobile 07738 626165
SP125 Limited Disclaimer
Honda, HRC and all other parts supplied by the SP125 Limited are not guaranteed when used in competition events.
As such, it is a condition of our making all parts available that it is solely the decision of each individual, rider, team member or
team whether they choose to use any part supplied and in doing so, absolve the manufacturer and SP125 Limited of any or all
such claims, including damage to equipment and/or injury to personnel irrespective of how caused.
All parts remain property of SP125 Limited until paid for in full.
All 'special order' parts, that are ordered specially under the instruction of the customer, are non returnable and non refundable.
Honda, HRC and all other parts supplied by the SP125 Limited are not guaranteed when used in competition events.
As such, it is a condition of our making all parts available that it is solely the decision of each individual, rider, team member or
team whether they choose to use any part supplied and in doing so, absolve the manufacturer and SP125 Limited of any or all
such claims, including damage to equipment and/or injury to personnel irrespective of how caused.
All parts remain property of SP125 Limited until paid for in full.
All 'special order' parts, that are ordered specially under the instruction of the customer, are non returnable and non refundable.
