HONDA RS125 NEW HANDLEBARS, LEVERS & FOOTPEGS 2021
Please 'Refresh' this page every time you visit. If it is slow to reload, you know then that this page has been updated since your last visit.
HONDA RS125 HANDLEBARS & LEVERS
1995~2004> 22mm FORWARD EXTENDED HANDLEBAR CLAMPS - Pair (for standard Honda RS125 Forks Ø 44mm) £165.00 + VAT
1995~2004> 22mm FORWARD EXTENDED HANDLEBAR CLAMPS - Pair (for Ohlins Forks Ø 45mm) £165.00 + VAT
1995~2004> 22mm FORWARD EXTENDED HANDLEBAR CLAMPS - Pair (for Ohlins Forks Ø 45mm) £165.00 + VAT
|
|
1988~2004> BATTLE FACTORY ALUMINIUM HANDLEBAR - with nylon end cap £16.50 + VAT each
1988~2004> BATTLE FACTORY HANDLEBAR END CAP £2.50 + VAT each
1988~2004> BATTLE FACTORY HANDLEBAR END CAP £2.50 + VAT each
|
|
|
RENTHAL HANDLEBAR GRIPS
Road Race Full Diamond Handlebar Grips £10.00 + Vat per pair (x2 Grips)
'Soft' Light Grey G147
'Medium' Grey G148
'Firm' Dark Grey G149
Road Race Full Diamond Handlebar Grips £10.00 + Vat per pair (x2 Grips)
'Soft' Light Grey G147
'Medium' Grey G148
'Firm' Dark Grey G149
HONDA RS125 BREMBO BRAKE LEVERS
BREMBO BRAKE LEVER - Standard 250 length £43.50 + VAT
BREMBO BRAKE LEVER - Short 125 length £45.00 + VAT
BREMBO BRAKE LEVER - Short 125 length £45.00 + VAT
Top: Brembo Short 18 Front Brake Lever
Bottom: Brembo Standard Front Brake Lever
BREMBO 'FOLDING' BILLET BRAKE LEVER - Short 18 length £73.00 + VAT
BREMBO 'FOLDING' BILLET BRAKE LEVER - Standard 250 length £73.00 + VAT
BREMBO 'FOLDING' BILLET BRAKE LEVER - Standard 250 length £73.00 + VAT
HONDA RS125 FRONT BRAKE LEVER PROTECTOR
Honda RS125 FRONT BRAKE LEVER PROTECTOR - RIGHT SIDE ONLY - PROGUARD SYSTEM £48.00 + VAT
Suitable for all 22mm handlebars with hollow ends and minimum inside diameter 14mm to maximum inside diameter 20mm
Please note: If using the Battle Factory Handlebars, it is necessary to turn around the handlebars to use the smaller inside diameter end.
We would advise using Loctite 243 threadlocker on all nuts and adjuster grub screws.
Honda RS125 FRONT BRAKE LEVER PROTECTOR - RIGHT SIDE ONLY - PROGUARD SYSTEM £48.00 + VAT
Suitable for all 22mm handlebars with hollow ends and minimum inside diameter 14mm to maximum inside diameter 20mm
Please note: If using the Battle Factory Handlebars, it is necessary to turn around the handlebars to use the smaller inside diameter end.
We would advise using Loctite 243 threadlocker on all nuts and adjuster grub screws.
|
|
|
1995/2004 RS125 Honda FRONT BRAKE LEVER PROTECTOR - RIGHT SIDE ONLY - GB RACING £48.00 + VAT
GB Racing Front Brake Lever Guard : For 16~17mm Internal Handlebar Tube Diameter
GB Racing Front Brake Lever Guard : For 16~17mm Internal Handlebar Tube Diameter
- Revolutionary new tough, high-impact composite material made from 60% Long Glass Fibered Nylon
- PATENT # GB2479405 for Improved Composition
|
|
|
HONDA RS125 CLUTCH LEVERS
1988~2004> PATTERN CLUTCH LEVER £18.00 + VAT
HONDA RS125 FOOTPEGS HANGERS, FOOTPEGS, GEAR & REAR BRAKE LEVERS
1995~2004> RCD GP PATTERN FOOTPEG (Threaded fixing) with Nylon End Cap £17.50 + VAT each
Machine Cut Grooves, giving superior grip over conventional knurled finished footpegs.
Fitted with solid Black Acetal End Cap.
Machined 19mm slot for easy installation / removal using a 19mm spanner.
8mm Threaded Mounting.
Total Length including End Cap : 80mm / Centre Outside Diameter : 24mm / End Outside Diameter : 26mm
Machine Cut Grooves, giving superior grip over conventional knurled finished footpegs.
Fitted with solid Black Acetal End Cap.
Machined 19mm slot for easy installation / removal using a 19mm spanner.
8mm Threaded Mounting.
Total Length including End Cap : 80mm / Centre Outside Diameter : 24mm / End Outside Diameter : 26mm
|
|
|
|
1990~2004> BATTLE FACTORY FOOTPEG (Threaded fixing) with Nylon End Cap & Stud for GP Bearing Lever £22.50 + VAT each
|
|
1990~2004> SPEEDFIBER FOOTPEG with Nylon End Cap £22.50 + VAT each
Please Note: The Speedfiber Footpegs are not threaded.
They have a 8.25mm straight hole and need to be bolted to the footrest hanger, using an 8mm Cap Screw. (*Screws not supplied)
|
|
|
HONDA RS125 FOOTREST HANGERS
1995~2004> RCD PATTERN FOOTREST HANGER PLATE - Stronger & Lighter Than Standard - CNC Machined £42.50 + VAT each
Fits to both Left & Right Sides
Stronger & Lighter than Standard Honda (255g)
CNC Machined from solid billet 6082 t6 Aerospace grade aluminium.
Fits to both Left & Right Sides
Stronger & Lighter than Standard Honda (255g)
CNC Machined from solid billet 6082 t6 Aerospace grade aluminium.
|
|
|
HONDA RS125 FOOTREST HANGER EXTENSION PLATES & EXTENDED GEARCHANGE RODS
1995~2004> FOOTREST HANGER EXTENSION PLATE SET £39.00 + VAT
These plates allow you to keep your existing footrest hangers and move them back either 13 mm, 25 mm or 38 mm
Made from high quality HE30 aluminium
Note: Necessary to use extended gear change rod.
Standard Length Gearchange Rod 243mm £10.00 + VAT
13mm Extended Length Gearchange Rod 256mm £10.00 + VAT
25mm Extended Length Gearchange Rod 268mm £10.00 + VAT
38mm Extended Length Gearchange Rod 281mm £10.00 + VAT
These plates allow you to keep your existing footrest hangers and move them back either 13 mm, 25 mm or 38 mm
Made from high quality HE30 aluminium
Note: Necessary to use extended gear change rod.
Standard Length Gearchange Rod 243mm £10.00 + VAT
13mm Extended Length Gearchange Rod 256mm £10.00 + VAT
25mm Extended Length Gearchange Rod 268mm £10.00 + VAT
38mm Extended Length Gearchange Rod 281mm £10.00 + VAT
|
Picture above shows a footrest hanger mounted at 38mm Extended
|
HONDA RS125 BATTLE FACTORY GEAR CHANGE RODS
Battle Factory Gear Change Rods, for use with the Battle Factory Quickshifter
Genuine Battle Factory 2017 Standard Length Gearchange Rod 189mm £31.50
Battle Factory 1995~2016 Standard Length Gearchange Rod 160mm £31.50
Battle Factory 1995~2016 20mm Extended Length Gearchange Rod 180mm £31.50
Battle Factory 1995~2016 50mm Extended Length Gearchange Rod 210mm £35.50
Genuine Battle Factory 2017 Standard Length Gearchange Rod 189mm £31.50
Battle Factory 1995~2016 Standard Length Gearchange Rod 160mm £31.50
Battle Factory 1995~2016 20mm Extended Length Gearchange Rod 180mm £31.50
Battle Factory 1995~2016 50mm Extended Length Gearchange Rod 210mm £35.50
|
|
HONDA RS125 GEAR & REAR BRAKE LEVERS
1990~2004> Honda RS125 SpeedFiber Lightweight Gear Lever £80.00 + VAT
Gear Lever End can be moved 7.5mm closer towards the footpeg, which helps smaller riders who have small feet.
Gear Lever End can be moved 7.5mm closer towards the footpeg, which helps smaller riders who have small feet.
|
|
|
1990~2004> Honda RS125 SpeedFiber Lightweight Rear Brake Lever £80.00 + VAT
1990~2004> Honda RS125 SpeedFiber Lightweight Rear Brake Lever £80.00 + VAT
|
|
|
1990~2004> BATTLEFACTORY G.P. SPEC BEARING TYPE GEAR LEVER - Increased Leverage & No Side Play £84.50 + VAT
1990~2004> BATTLEFACTORY G.P. SPEC BEARING TYPE REAR BRAKE LEVER - No Side Play £84.50 + VAT
|
|
|
HONDA RS125 FOOTREST HANGER & LEVER COMPLETE SETS
1995~2004> BATTLE FACTORY FOOTREST HANGER SET - Footpeg Position Standard £325.00 + VAT
|
|
|
BATTLE FACTORY LEVER REPLACEMENT PARTS
1990~2004> BATTLE FACTORY Replacement Lever End £21.00 + VAT
1990~2004> BATTLE FACTORY Replacement Lever Bearing (x2 in each lever) £12.00 + VAT each
1990~2004> BATTLE FACTORY Replacement Lever Aluminium Collar (28x2.5x2) for pack of x2 £5.75 + VAT
1990~2004> BATTLE FACTORY Replacement Lever Shim Washer (8x0.5x4) for pack of x4 £1.20 + VAT
|
|
HONDA RS125 SPEEDFIBER GEAR LEVER & REAR BRAKE LEVER END
1990~2004> SpeedFiber Replacement Lever End (Length 40mm & Rubber Diameter 17mm) £10.00 + VAT
|
|
Exports of all parts supplied outside of UK, to EU Countries, USA, Australia, South Africa, Asia etc are exempt from UK VAT and will be charged 0% VAT.
On arrival to your destination country, you may be asked to pay additional duties and taxes by customs, before the shipment is delivered.
Import tax, customs & duties regulations vary from country to country.
Payment of all Import tax, customs & duties charges are the responsibility of the customer.
On arrival to your destination country, you may be asked to pay additional duties and taxes by customs, before the shipment is delivered.
Import tax, customs & duties regulations vary from country to country.
Payment of all Import tax, customs & duties charges are the responsibility of the customer.
SP125 Limited
22 Walker Wood, Baildon, Shipley, West Yorkshire, BD17 5BE, England
Telephone 01274 583231 steve@sp125racing.com Mobile 07738 626165
22 Walker Wood, Baildon, Shipley, West Yorkshire, BD17 5BE, England
Telephone 01274 583231 steve@sp125racing.com Mobile 07738 626165
SP125 Limited Disclaimer
Honda, HRC and all other parts supplied by the SP125 Limited are not guaranteed when used in competition events.
As such, it is a condition of our making all parts available that it is solely the decision of each individual, rider, team member or
team whether they choose to use any part supplied and in doing so, absolve the manufacturer and SP125 Limited of any or all
such claims, including damage to equipment and/or injury to personnel irrespective of how caused.
All parts remain property of SP125 Limited until paid for in full.
All 'special order' parts, that are ordered specially under the instruction of the customer, are non returnable and non refundable.
Honda, HRC and all other parts supplied by the SP125 Limited are not guaranteed when used in competition events.
As such, it is a condition of our making all parts available that it is solely the decision of each individual, rider, team member or
team whether they choose to use any part supplied and in doing so, absolve the manufacturer and SP125 Limited of any or all
such claims, including damage to equipment and/or injury to personnel irrespective of how caused.
All parts remain property of SP125 Limited until paid for in full.
All 'special order' parts, that are ordered specially under the instruction of the customer, are non returnable and non refundable.
