HONDA RS125 & NSF250R NEW BRAKES, DISCS & BRAKE PADS 2024
Please 'Refresh' this page every time you visit. If it is slow to reload, you know then that this page has been updated since your last visit.
HONDA RS125 & NSF250R REAR BRAKE PADS
1990~2019 Honda RS125 & NSF250R EBC STANDARD REAR BRAKE PADS (Pair) £19.50 + VAT
|
|
|
HONDA RS125 & NSF250R REAR BRAKE DISCS
EBC PATTERN REAR BRAKE DISC - Copy of original Honda Rear Brake Disc 43122-NF5-760 (Weight 530g) Ø186mm X 4.0mm thick £82.00 + VAT
|
|
|
GALFER WAVE LIGHTWEIGHT REAR BRAKE DISC (Weight 320g) Ø185mm X 4.0mm thick £80.00 + VAT
|
|
|
STAINLESS STEEL LIGHTWEIGHT REAR BRAKE DISC (Weight 390g) Ø185mm X 4.0mm thick £85.00 + VAT
STAINLESS STEEL LIGHTWEIGHT REAR BRAKE DISC (Weight 390g) Ø185mm X 4.0mm thick £85.00 + VAT
|
|
|
BREMBO BRAKES
|
|
BREMBO 16x18 RADIAL FRONT BRAKE MASTERCYLINDER - including Brake Lever - 16mm bore, 18-ratio lever, 286g £215.00 + VAT
|
|
|
BREMBO FRONT BRAKE MASTERCYLINDER REPAIR KIT £47.50
Genuine Brembo Mastercylinder repair kit - to repair damaged push rod and crush washer
Genuine Brembo Mastercylinder repair kit - to repair damaged push rod and crush washer
Brembo 16x18 Front Brake Mastercylinder Remote Brake Fluid Reservoir Kit £31.50 + VAT
1x 30cc Reservoir, 1x Neoprene Hose 300mm, 2x Hose Clips, 1x M10x1 Banjo Bolt & 2x Copper Washers
1x 30cc Reservoir, 1x Neoprene Hose 300mm, 2x Hose Clips, 1x M10x1 Banjo Bolt & 2x Copper Washers
|
|
|
|
|
BREMBO RESERVOIRS
BREMBO RESERVOIR 30cc - standard size with straight outlet £18.00 + VAT
|
BREMBO RESERVOIR 15cc - small size with straight outlet £8.50 + VAT
|
BREMBO RESERVOIR 15cc - small size with 45 degree outlet £8.50 + VAT
|
BREMBO FRONT BRAKE LEVERS
Brembo 'Short' 18 Front Brake Lever £45.00 + VAT
Brembo 'Standard' Front Brake Lever £45.00 + VAT
Brembo 'Standard' Front Brake Lever £45.00 + VAT
BREMBO 'FOLDING' BILLET BRAKE LEVER - Short 18 length £72.00 + VAT
BREMBO 'FOLDING' BILLET BRAKE LEVER - Standard 250 length £72.00 + VAT
BREMBO 'FOLDING' BILLET BRAKE LEVER - Standard 250 length £72.00 + VAT
BREMBO MASTERCYLINDER PARTS
|
Brembo Lever PIVOT PIN £2.50 + VAT
|
Brembo Lever Pivot Pin RETAINING CLIP £0.75 + VAT
|
|
Brembo Lever BARREL NUT £38.00 + VAT
|
Brembo Lever KNURLED ADJUSTER KNOB £10.00 + VAT
|
|
Brembo Bleed nipple £4.75 + VAT
|
Brembo Bleed nipple cover £1.50 + VAT
|
|
Brembo M10 x 1 Single Banjo Bolt £4.25 + VAT
|
Brembo Clip for reservoir hose £1.00 + VAT
|
Brembo Neoprene Hose 300mm Length £6.00 + VAT
GALFER FRONT BRAKE PADS
GALFER Sintered Front Brake Pads - For the Standard Honda NSF250R Nissin Caliper & Honda RS125 NX4 Standard Caliper £75.00 + VAT (Set - Pads x2)
GALFER Sintered Front Brake Pads - For the Standard Honda NSF250R Nissin Caliper & Honda RS125 NX4 Standard Caliper £75.00 + VAT (Set - Pads x2)
|
|
|
BREMBO Z04 BRAKE PADS
BREMBO Z04 Front Brake Pads - For the Standard Honda NSF250R Nissin Caliper & Honda RS125 NX4 Standard Caliper £95.00 + VAT (Set - Pads x2)
BREMBO Z04 Front Brake Pads - For the Standard Honda NSF250R Nissin Caliper & Honda RS125 NX4 Standard Caliper £95.00 + VAT (Set - Pads x2)
|
|
|
BREMBO Z04 BRAKE PADS
BREMBO Z04 8mm Sintered Front Brake Pads - Z04 Compound - for X10.48.14 Brembo GP & Radial XA3 Monobloc Caliper £110.00 + VAT (Set - Pads x2)
BREMBO Z04 10mm Sintered Front Brake Pads - Z04 Compound - for 2-Pad X97, X10.41 & XA9 Radial Monobloc Caliper £97.50 + VAT (Set - Pads x2)
BREMBO Z04 Sintered Front Brake Pads - Z04 Compound - for X99 4-Pad Radial Monobloc Caliper £225.00 + VAT (Set - Pads x4)
|
|
BREMBO BRAKE FLUID
Brembo LCF600 DOT4 BRAKE FLUID (500ml) £25.00 + VAT
HONDA RS125 & NSF250R GALFER BRAKE DISC
GALFER FULL FLOATING WAVE 296mm FRONT BRAKE DISC Ø296mm X 4.0mm thick (Weight 1.181g) 17mm OFFSET £185.00 + VAT
Full floating to ensure optimum brake pad-to-rotor contact.
Every high-quality, Galfer-patented Wave rotor is made from a proprietary mix of virgin high carbon 420 stainless steel, laser cut (never stamped), double disc-parallel ground to assure perfect parallel flatness and heat treated to each specific application.
KBA and TUV approved. Seamlessly replaces stock rotor. Full instructions provided
GALFER FULL FLOATING WAVE 296mm FRONT BRAKE DISC Ø296mm X 4.0mm thick (Weight 1.181g) 17mm OFFSET £185.00 + VAT
Full floating to ensure optimum brake pad-to-rotor contact.
Every high-quality, Galfer-patented Wave rotor is made from a proprietary mix of virgin high carbon 420 stainless steel, laser cut (never stamped), double disc-parallel ground to assure perfect parallel flatness and heat treated to each specific application.
KBA and TUV approved. Seamlessly replaces stock rotor. Full instructions provided
|
|
|
HONDA RS125 & NSF250R BREMBO BRAKE DISC 290mm
BREMBO 290mm FRONT BRAKE DISC 15mm OFFSET - Fully Floating, Drilled Cast Stainless Steel Rotor with machined Aluminium Center
£340.00 + VAT
Please note: Brembo measure the offset from the Disc Carrier to the centre of the brake disc.
£340.00 + VAT
Please note: Brembo measure the offset from the Disc Carrier to the centre of the brake disc.
HONDA RS125 & NSF250R BREMBO BRAKE DISC 300mm
BREMBO HPK 300mm FRONT BRAKE DISC 15mm OFFSET - Fully Floating, Drilled Cast Stainless Steel Rotor with machined Aluminium Center
(Weight 1.48g) Ø300mm X 5.5mm thick £230.00 + VAT
Please note: Brembo measure the offset from the Disc Carrier to the centre of the brake disc.
Supplied with 4x 1mm Spacers to move outwards the Nissin Brake Caliper by 2mm.
This due to the Brembo Brake Disc size 300mm, against the Standard Honda Brake Disc, which is 296mm.
BREMBO HPK 300mm FRONT BRAKE DISC 15mm OFFSET - Fully Floating, Drilled Cast Stainless Steel Rotor with machined Aluminium Center
(Weight 1.48g) Ø300mm X 5.5mm thick £230.00 + VAT
Please note: Brembo measure the offset from the Disc Carrier to the centre of the brake disc.
Supplied with 4x 1mm Spacers to move outwards the Nissin Brake Caliper by 2mm.
This due to the Brembo Brake Disc size 300mm, against the Standard Honda Brake Disc, which is 296mm.
|
|
HONDA RS125 & NSF250R 2004~2018 BREMBO RADIAL FRONT BRAKE CALIPERS
BREMBO XA3 RADIAL 2-PIECE FRONT BRAKE CALIPER - Two versions available.
For use with Standard Honda 297mm or brembo 290mm front brake discs & Z04 8mm Brake Pads.
BREMBO XA3.B8.61 2-Piece Body Machined from Solid Aluminium, with Aluminium 4 Piston, with Racing Spec Seals & Quick Release Pad Pin.
£760.00 + VAT
BREMBO XA3.B8.31 2-Piece Body Machined from Solid Aluminium, with Titanium 4 Piston & Bolts, with Racing Spec Seals & Quick Release Pad Pin.
£1,040.00 + VAT
Excellent performance upgrade for replacing standard calipers at a lower price than Monobloc versions.
For use with Standard Honda 297mm or brembo 290mm front brake discs & Z04 8mm Brake Pads.
BREMBO XA3.B8.61 2-Piece Body Machined from Solid Aluminium, with Aluminium 4 Piston, with Racing Spec Seals & Quick Release Pad Pin.
£760.00 + VAT
BREMBO XA3.B8.31 2-Piece Body Machined from Solid Aluminium, with Titanium 4 Piston & Bolts, with Racing Spec Seals & Quick Release Pad Pin.
£1,040.00 + VAT
Excellent performance upgrade for replacing standard calipers at a lower price than Monobloc versions.
|
Replacement Seals for Brembo XA3 Caliper
BREMBO LOW DRAG SEAL 32mm £12.00 + VAT Each BREMBO LOW DRAG SEAL 36mm £12.00 + VAT Each |
BREMBO X97.37.61 RADIAL MONOBLOC FRONT BRAKE CALIPER (2-Pad) - For use with Standard Honda 297mm or brembo 290mm front brake discs & Z04 10mm Brake Pads.
1-Piece Body Machined from Solid Aluminium with 32/36 Titanium 4 Pot with Racing Spec Seals Quick release Titanium pad pin. No pads included.
Radial Mounted 108mm mounting hole centres. Weight 660g
This is a true single piece caliper + with radial fixing gives further improvements in consistency and braking power. £1,501.50 + VAT
1-Piece Body Machined from Solid Aluminium with 32/36 Titanium 4 Pot with Racing Spec Seals Quick release Titanium pad pin. No pads included.
Radial Mounted 108mm mounting hole centres. Weight 660g
This is a true single piece caliper + with radial fixing gives further improvements in consistency and braking power. £1,501.50 + VAT
Replacement Seals for Brembo X97 Caliper
BREMBO LOW DRAG SEAL 32mm £12.00 + VAT Each
BREMBO LOW DRAG SEAL 36mm £12.00 + VAT Each
BREMBO LOW DRAG SEAL 32mm £12.00 + VAT Each
BREMBO LOW DRAG SEAL 36mm £12.00 + VAT Each
BREMBO X99.C4.61 RADIAL MONOBLOC FRONT BRAKE CALIPER (4-Pad) - For use with Standard Honda 297mm or brembo 290mm front brake discs
It is a true single piece caliper, using 4 pads per caliper giving higher initial bite, braking power and consistency. £1760.00 + VAT
It is a true single piece caliper, using 4 pads per caliper giving higher initial bite, braking power and consistency. £1760.00 + VAT
60mm BOLTS & 10mm SPACER KIT for fitting BREMBO X97 CALIPER to standard 2004/07 honda forks & using BREMBO 290mm DISK. £35.00 + VAT
70mm BOLTS & 10mm SPACER KIT for fitting BREMBO XA3 & X99 CALIPER to standard 2004/07 honda forks & using BREMBO 290mm DISK. £35.00 + VAT
80mm BOLTS & 13mm SPACER KIT for fitting BREMBO RADIAL CALIPER to standard 2004/07 honda forks & using Honda 296mm DISK. £35.00 + VAT
70mm BOLTS & 10mm SPACER KIT for fitting BREMBO XA3 & X99 CALIPER to standard 2004/07 honda forks & using BREMBO 290mm DISK. £35.00 + VAT
80mm BOLTS & 13mm SPACER KIT for fitting BREMBO RADIAL CALIPER to standard 2004/07 honda forks & using Honda 296mm DISK. £35.00 + VAT
HONDA RS125 1995~2003 BREMBO FRONT BRAKE CALIPERS
BREMBO 20.5165.68 STANDARD 45100-NX4-770 GOLDLINE FRONT BRAKE CALIPER
For use only with standard 297mm front brake disc
Standard Cast Aluminium 2-Piece Body with 30/34 Aluminium 4 Pot with Dust Seals £190.00 + VAT
For use only with standard 297mm front brake disc
Standard Cast Aluminium 2-Piece Body with 30/34 Aluminium 4 Pot with Dust Seals £190.00 + VAT
BREMBO 20.4756.62 BILLET 2-PIECE FRONT BRAKE CALIPER - for use only with standard 297mm front brake disc
2-Piece Body Machined from Solid Aluminium, with 30/34 Aluminium 4 Piston, with Racing Spec Seals & Quick Release Pad Pin.
40mm mounting hole centres. Weight 780g £525.00 + VAT
2-Piece Body Machined from Solid Aluminium, with 30/34 Aluminium 4 Piston, with Racing Spec Seals & Quick Release Pad Pin.
40mm mounting hole centres. Weight 780g £525.00 + VAT
Replacement Seals for BREMBO 20.4756.62 BILLET 2-PIECE FRONT BRAKE CALIPER £46.00 + VAT
Replacement Brake Pads for BREMBO 20.4756.62 BILLET 2-PIECE FRONT BRAKE CALIPER £97.50 + VAT
(Set = Pads x2) Brembo Z04 Pads 107.A486.53
(Set = Pads x2) Brembo Z04 Pads 107.A486.53
BREMBO FRONT BRAKE CALIPER PARTS
R-CLIP for BREMBO BILLET, X10, XA3, X97 CALIPER £4.00 + VAT
R-CLIP for BREMBO X99 4-PAD RADIAL MONOBLOC CALIPER £11.00 + VAT
R-CLIP for BREMBO X99 4-PAD RADIAL MONOBLOC CALIPER £11.00 + VAT
|
PAD PIN & R-CLIP for BREMBO BILLET 2-PIECE CALIPER
PAD PIN for X10 BREMBO MONOBLOC CALIPER PAD PIN for XA3 BREMBO 2-PIECE RADIAL CALIPER (Length 55mm x OD 6mm) PAD PIN for X97 BREMBO RADIAL MONOBLOC CALIPER PAD PIN for X99 BREMBO 4-PAD RADIAL MONOBLOC CALIPER |
£25.00 + VAT
£37.50 + VAT £38.50 + VAT £42.00 + VAT £55.00 + VAT |
PAD SPRING for BREMBO X99 4-PAD RADIAL MONOBLOC CALIPER £37.50 + VAT
PAD SPRING for BREMBO X99 4-PAD RADIAL MONOBLOC CALIPER £37.50 + VAT
PAD SPRING for BREMBO Moto3 XA 88810/11 TWIN DISC CALIPERS £37.50 + VAT
PAD SPRING for BREMBO X99 4-PAD RADIAL MONOBLOC CALIPER £37.50 + VAT
PAD SPRING for BREMBO Moto3 XA 88810/11 TWIN DISC CALIPERS £37.50 + VAT
HONDA RS125 & NSF250R 1995~2018 BREMBO REAR BRAKE CALIPER
BREMBO RACING REAR BRAKE CALIPER X20.60.01 £690.00 + VAT
BREMBO REAR BRAKE CALIPER Brake Pads 07.9340.90 £27.50 + VAT each
PAD PIN for BREMBO REAR BRAKE CALIPER £10.00 + VAT
Replacement XA3.45.01 Seals for Brembo X20.60.01 Rear Caliper
BREMBO LOW DRAG SEAL 24mm £11.75 + VAT Each
BREMBO LOW DRAG SEAL 24mm £11.75 + VAT Each
PAD SPRING for BREMBO REAR BRAKE CALIPER £37.50 + VAT
BREMBO BANJO BOLT - WITH BRAKE LIGHT SWITCH
Brembo Banjo Bolt - With Brake Light Switch - for single banjo Brembo MasterCylinders £19.00 + VAT
Brembo Banjo Bolt - With Brake Light Switch - for double banjo Brembo MasterCylinders £19.00 + VAT
Brembo Banjo Bolt - With Brake Light Switch - for double banjo Brembo MasterCylinders £19.00 + VAT
BREMBO 16x18 REMOTE BRAKE ADJUSTER
BREMBO TWM Straight Remote Brake Lever Adjuster - 565mm long £126.00 + VAT
BREMBO TWM Straight Remote Brake Lever Adjuster - 715mm long (Most Popular Length) £126.00 + VAT
BREMBO Roll pin for racing cylinders to fix pushrod knob £0.60 + VAT
BREMBO TWM Straight Remote Brake Lever Adjuster - 715mm long (Most Popular Length) £126.00 + VAT
BREMBO Roll pin for racing cylinders to fix pushrod knob £0.60 + VAT
|
|
The remote adjuster has become an integral part of all racing brake systems.
One end is attached to the brake lever span adjuster, the other end is mounted on the opposite side of the handle bar, and this enables the rider to adjust the lever span while keeping control of the throttle.
Probably used by every team and rider that runs a racing brake system.
Primarily designed for use with Brembo racing cylinders but can also be adapted for use with any brake cylinder that features lever span adjustment.
One end is attached to the brake lever span adjuster, the other end is mounted on the opposite side of the handle bar, and this enables the rider to adjust the lever span while keeping control of the throttle.
Probably used by every team and rider that runs a racing brake system.
Primarily designed for use with Brembo racing cylinders but can also be adapted for use with any brake cylinder that features lever span adjustment.
BREMBO Remote Brake Adjuster Clamp - Tall & Split Swivel Adjustable Angle £31.25 + VAT
Thickness – 9mm at bar end & 6mm in centre.
Height is 60mm from top of handlebar.
Made from Teflon
Thickness – 9mm at bar end & 6mm in centre.
Height is 60mm from top of handlebar.
Made from Teflon
Exports of all parts supplied outside of UK, to EU Countries, USA, Australia, South Africa, Asia etc are exempt from UK VAT and will be charged 0% VAT.
On arrival to your destination country, you may be asked to pay additional duties and taxes by customs, before the shipment is delivered.
Import tax, customs & duties regulations vary from country to country.
Payment of all Import tax, customs & duties charges are the responsibility of the customer.
On arrival to your destination country, you may be asked to pay additional duties and taxes by customs, before the shipment is delivered.
Import tax, customs & duties regulations vary from country to country.
Payment of all Import tax, customs & duties charges are the responsibility of the customer.
SP125 Limited
22 Walker Wood, Baildon, Shipley, West Yorkshire, BD17 5BE, England
Telephone 01274 583231 [email protected] Mobile 07738 626165
22 Walker Wood, Baildon, Shipley, West Yorkshire, BD17 5BE, England
Telephone 01274 583231 [email protected] Mobile 07738 626165
SP125 Limited Disclaimer
Honda, HRC and all other parts supplied by the SP125 Limited are not guaranteed when used in competition events.
As such, it is a condition of our making all parts available that it is solely the decision of each individual, rider, team member or
team whether they choose to use any part supplied and in doing so, absolve the manufacturer and SP125 Limited of any or all
such claims, including damage to equipment and/or injury to personnel irrespective of how caused.
All parts remain property of SP125 Limited until paid for in full.
All 'special order' parts, that are ordered specially under the instruction of the customer, are non returnable and non refundable.
Honda, HRC and all other parts supplied by the SP125 Limited are not guaranteed when used in competition events.
As such, it is a condition of our making all parts available that it is solely the decision of each individual, rider, team member or
team whether they choose to use any part supplied and in doing so, absolve the manufacturer and SP125 Limited of any or all
such claims, including damage to equipment and/or injury to personnel irrespective of how caused.
All parts remain property of SP125 Limited until paid for in full.
All 'special order' parts, that are ordered specially under the instruction of the customer, are non returnable and non refundable.
